How To Paint A Room - Painting Tips

Hello again out there painting fans, Cheap Calgary Painter here again. Taking time to perform a thorough interior painting surface prep and painting in an orderly systematic way are the keys to getting professional looking results when doing any type of paint project. In this here quick, fast, and easy How To Paint A Room - Painting Tips blog post, we cover the basics again in detail. 

Skimping on the prep work is probably the biggest mistake people make when painting. Take the time and do it right. Our cheap Calgary Painting team can help. It really does affect the end result. 

How To Paint A Room Fast.

First, make sure the House Painter carefully inspect walls for cracks, holes, dents, dings, scratches, drips, bad rolling marks, bad spray marks, or other surface imperfections, etc, before priming or painting. Use a lightweight spackling compound and putty knife to fill and repair any holes or imperfections. Then remove any excess spackling with the putty knife while the spackling is still wet and allow the area to dry completely. Hopefully your House Painting Estimate covers this part of the job.

Once dry use a small piece of very fine 220-grit sandpaper or a sanding sponge to smooth the repaired areas, flush with the surface. Sanding sponges work better to make a flatter surface in the end. You could also wrap some sand paper around a block of wood or any other flat surface and use that to grind down the spackle. Once you sand down each spot, grab a poll sander with a sanding head and poll sand down all the walls.

How To Paint A Room To Make It Look Bigger.

Wipe the walls clean with a damp towel or sponge, and allow an appropriate amount of time for them to dry before priming or painting. This part is optional as we've tried cleaning the walls with a towel and just simply painting after sanding, and the finish results are the same across all of the different brands, colors, and types of paint sheens we have tried these methods on.

You should also make sure the walls are clean and free from dust. You'd be surprised how much dust actually builds up on walls over time. Be sure you do a good sanding with the poll sander to get all the dust and junk off the wall. Be on the look out for chunks of dried paint bits and paint drips from the last professional painter or decorator that painted your home.

How To Paint A Room With A Roller.

Harder to reach, and out of the way areas, corners, and areas behind furniture can also have lots of cobwebs. Use something like a floor duster to wipe the walls clean or simply re sand it all off to help ensure paint applies evenly and you don't paint over junk or crap on the surfaces. 

Painter's tape is used to help you achieve clean, professional-looking results. Its primary purpose is to protect areas you don't intend to paint. It's perfect for door and window trim, molding and baseboards. It helps you create sharp clean lines, paint stripes or patterns and create two-tone wall effects. There are different adhesion levels for painter's tape. 

How To Paint A Room Professionally.

All are meant to be easily removed. But some stick a little more firmly than others. While some are perfect for textured surfaces, others are intended for more delicate areas like a freshly painted wall, finished hardwood or wallpaper. Be sure and check which adhesion level is right for the job you're doing. 

If your ceiling is non-textured - or if you have crown molding you'll want to mask that off, where it meets the edge of the wall. Apply your tape in short, overlapping, strips pressing down firmly along the edge. If you don't take the time to apply painter's tape properly, you can experience Bleed-Through. Paint can seep under the tape barrier and get on the protected surface. 

How To Paint A Room Step By Step.

Make sure your tape is flat and evenly pressed down. You can use your fingers or a putty knife. Paint will seep through at any point where the tape is not in full contact with the surface. Before doing any priming or painting you'll want to protect your floors with a drop cloth. There are three basic kinds: -- canvas, plastic and paper. Canvas drop cloths are extremely durable and absorbent.

So they can be used over and over again. Plastic is less expensive and durable, but isn't absorbent so spills won't dry as quickly and can be tracked through the room and stepped on. Paper is the most economical but can tear easily on floors. But they're perfect for covering other things like cabinets and furniture.

How To Paint A Room In One Day.

If you're working in an average- or small-sized room, you really should remove all the furniture. Any time you think you're saving by not doing this will be wasted throughout your project, because you will constantly be adjusting and relocating things to give yourself room. The final step of your paint, prep, is cutting in the room with primer. 

Cutting in is basically outlining the room and involves using a paintbrush to create two- to three-inch bands around the edges of the walls where they meet ceilings, baseboards other walls, door and window frames and hinges. Those two- to three-inch areas around the room allow you to roll the rest of the walk quickly without having to try and roll paint in those confined spaces. 

How To Paint A Room For Beginners.

It's impossible to use a roller that close to those areas you're trying not to paint without making mistakes. When cutting in many people choose to do the entire room at one time. This is a good option. And it is also how the professional painters do it.  If you want to finish in a hurry however, your border areas will probably dry before you overlap them. 

When painting the wall you may see a slight difference in sheen between the two coats because they won't be able to blend. If that's a concern, you should cut in and paint one wall at a time before moving on to others. You'll achieve a smoother more seamless look because you'll be able to blend the wet paint you've brushed on with the wet paint being rolled on. 

How To Paint A Room With Two Colors.

Priming your walls before painting is an important part of any painting project. Primers are specially designed to adhere to different types of surfaces and receive your top coat of paint. You also have the option of using a paint and primer in one. This will eliminate the need for separate coats of each and will save you time and money. 

When painting new drywall priming helps seal the wall and can help prevent mold. They also help when you're painting walls that are stained or when you're making a dramatic color change. Primers, can also be tinted at our store to closely match the color of your paint. Since primer is less expensive than paint using a tinted primer can help you cut down on the number of paint codes needed and save you money. 

How To Paint A Room White.

If you've made wall repairs, spackle and especially drywall compound, will draw out the moisture from the paint giving the area a dull look that is different from the rest of the wall. Priming will prevent this problem since you'll be painting directly over the primer and not the repair material. When applying your primer start by painting in three-foot by three-foot sections. 

Roll in one section at a time moving from top to bottom and from one side of the wall to the other with a fully loaded roller. Work top to bottom rolling back and forth across the wall in a series of V- or W-shaped strokes until the section is covered. Reload your roller and paint the next section, covering only as much as you can finish while the primer is still wet.

Always overlap areas of wet primer. This is a painting technique. The pros call working to a wet edge. The technique helps prevent streaking. After the primer is completely dry, lightly sand away bumps, ridges and other surface imperfections using very fine grit sandpaper folded into quarters. Or the good old tried and true sanding block to get flat sanding repair finishes and skip the bump.

When the grit of one section becomes covered with paint dust switch to an unused section and continue. Wipe the wall clean with a damp towel or sponge and allow it to dry. Before starting any paint job, it's always a good idea to remix your paint using a mixing stick or a paint-mixing tool like a drill and whip. In a pinch you can make sure the lid is firmly on the gallon and shake the paint can vigorously.

You should do this any time you leave your paint sitting for an extended period of time. The first step in painting your walls is to use a good-quality paint brush and cut in the room again this time with your paint. If you left your painter's tape on after priming, You can just paint over it again. If you removed your painter's tape, you'll need to reapply it before starting. 

A foolproof way of achieving clean and even paint edges is to avoid loading the brush down with too much paint. Aim small, miss small. The excess has to go somewhere and will probably end up where it doesn't belong. Begin painting by brushing onto the wall first and not the tape. Brush back and forth, until most of the paint has been applied.

Then when there's just a bit of paint left on the brush paint the area next to the tape and overlap your strokes onto the tape. That way, there will only be enough paint left on the brush to cover the remaining unpainted wall surface. And there won't be enough to seep under the tape.

To apply your top coat of paint follow the exact same process and techniques used when priming your walls. Roll in small, manageable three-foot by three-foot areas from the ceiling to the floor and from one side of the wall to the other. Blend your sections as you go. With a fully loaded roller work, top to bottom rolling back and forth across the wall in a series of V- or W-shaped strokes until the section is covered.

You want your roller fully covered with paint, but not to the point where it's dripping. Before reloading your roller and moving to the next section. Roll over the area you've just painted in a smooth, continuous stroke from top to bottom and back and forth without picking up the roller.

These smoothing strokes even the coat and help to cover up lines and paint roller tracks. As you overlap areas already painted lightly, lift the roller off the wall to avoid leaving end marks and to help blend different areas into one seamless, surface. 

Avoid the common mistake of painting straight up and down in rows from top to bottom unless you are an experienced professional painter. When you do this, it's harder to blend your paint evenly. And you can end up with a slight striped appearance, which you won't be happy with. Final step is to remove your painter's tape. Now you have two options.

You can do this just before the paint dries completely if you're concerned about the tape getting stuck in the paint. Or you can wait until the paint is dry. If left on too long sometimes small pieces of the tape can tear and get left behind when being removed. If you run into this use a utility knife to slice through the dried paint while pulling up the tape at a 45-degree angle.

Now tightly seal remaining paint in cans thoroughly and completely clean paint, brushes and rollers, and dispose of used painter's tape. Noticeable color variations in separate gallons of paint are rare now that mixtures are created by computers. But to be safe. Once you've used half a gallon of paint refill that can, with paint from a different can and remix.

If you're doing a large job, you can mix several gallons into one five-gallon bucket. That way, you'll be guaranteed color uniformity. Or just buy a 5 gallon pail to start with. You also have options for how you reload your paint roller. You can use a traditional and reliable paint tray. Or to avoid the possibility of stepping in your paint or having a pet wander through and causing a mess, you can roll from a bucket using a paint grid.

For optimum results in color quality and finish. A second coat may be needed. Just be sure and allow the first coats to dry completely, usually between two and four hours. The rule of thumb is that painting in the same colors again usually only require one coat of paint. Any color changes will need two more more coats of paint. That's just the way it is. On some extreme color changes you could be looking at painting four coats of paint or more.

Well, that's a wrap on our how to paint a room - painting tips blog post. Painting over all is easy and just about anyone can do it. If you don't know How To Paint A House Interior you will probably make a mess. But the best and most certain and best looking results will likely come from hiring in a professional house painter or a painting contractor. Your best bet is hiring in a professional house painter that basically only does house painting. Our Painting And Decorating Prices might appeal to you and be in your budget.

At 1/2 Price Pro Calgary Painting, we are committed to helping you keep your painting costs and your painting prices in Calgary down to the lowest prices possible. It's competitive out there. Give us a call and we can probably help you save a lot of time and a lot of money on professional painting and decorating services in Calgary, Alberta, Canada.